F5F Stay Refreshed Hardware Desktop Activating D.O.C.P. (xmp) together with operating rams at their designed velocities causes system instability.

Activating D.O.C.P. (xmp) together with operating rams at their designed velocities causes system instability.

Activating D.O.C.P. (xmp) together with operating rams at their designed velocities causes system instability.

Pages (2): Previous 1 2
A
Agman10
Senior Member
690
06-29-2018, 10:02 AM
#11
Memtest is completing with near-perfect results after 25 minutes. Would you like to keep it running for longer—up to an hour or more? Note: This was a 100% success rate in the initial test. — Edited December 29, 2019 by TheVan28
A
Agman10
06-29-2018, 10:02 AM #11

Memtest is completing with near-perfect results after 25 minutes. Would you like to keep it running for longer—up to an hour or more? Note: This was a 100% success rate in the initial test. — Edited December 29, 2019 by TheVan28

S
StormGaming
Junior Member
21
07-18-2018, 12:18 AM
#12
Sure, I understand. Let's keep it concise.
S
StormGaming
07-18-2018, 12:18 AM #12

Sure, I understand. Let's keep it concise.

P
Pigeonix_YT
Junior Member
4
07-18-2018, 11:53 PM
#13
Check the situation for 1 hour and 35 minutes. If issues persist, try raising the voltage to 1.37 and monitor the results with the PC regularly.
P
Pigeonix_YT
07-18-2018, 11:53 PM #13

Check the situation for 1 hour and 35 minutes. If issues persist, try raising the voltage to 1.37 and monitor the results with the PC regularly.

M
MeGustaElSexo
Member
173
07-20-2018, 02:01 AM
#14
A bit more voltage would help XMP run smoothly with your setup—it's currently around 1.37V. No issues detected, just ensure stability is achieved. Also, confirm the RAM is placed in the right slots: A2 and B2, which are the second and fourth slots from the CPU end.
M
MeGustaElSexo
07-20-2018, 02:01 AM #14

A bit more voltage would help XMP run smoothly with your setup—it's currently around 1.37V. No issues detected, just ensure stability is achieved. Also, confirm the RAM is placed in the right slots: A2 and B2, which are the second and fourth slots from the CPU end.

X
xFqtal_
Senior Member
670
07-20-2018, 11:33 PM
#15
Used levels A2 and B2. Raised voltage to 3.7, will notify upon failure.
X
xFqtal_
07-20-2018, 11:33 PM #15

Used levels A2 and B2. Raised voltage to 3.7, will notify upon failure.

S
Sheylizs
Member
81
07-21-2018, 10:37 PM
#16
3.7 volts? Wow... (I realize that was a mistake)
S
Sheylizs
07-21-2018, 10:37 PM #16

3.7 volts? Wow... (I realize that was a mistake)

N
nikkoset
Junior Member
14
07-23-2018, 05:03 PM
#17
Absolutely, it's very reliable.
N
nikkoset
07-23-2018, 05:03 PM #17

Absolutely, it's very reliable.

M
mike_power
Junior Member
12
07-23-2018, 08:40 PM
#18
Last night there were no crashes, but today at 5 minutes after powering on the PC it crashes. I'm planning to try a 2933 MHz clock at 1.37 GHz next.
M
mike_power
07-23-2018, 08:40 PM #18

Last night there were no crashes, but today at 5 minutes after powering on the PC it crashes. I'm planning to try a 2933 MHz clock at 1.37 GHz next.

L
Lorddoom139
Posting Freak
956
07-23-2018, 08:56 PM
#19
System stayed steady by retaining docp while reducing RAM speed to 2933 (still at 1.35 volts). Problem resolved.
L
Lorddoom139
07-23-2018, 08:56 PM #19

System stayed steady by retaining docp while reducing RAM speed to 2933 (still at 1.35 volts). Problem resolved.

Pages (2): Previous 1 2