F5F Stay Refreshed Hardware Desktop Access issues with Gigabyte MZ01-CE0 webui and no screen output.

Access issues with Gigabyte MZ01-CE0 webui and no screen output.

Access issues with Gigabyte MZ01-CE0 webui and no screen output.

X
x15Ghost15x
Member
Find
183
04-04-2016, 11:35 AM
#1
Hello! I’m really pleased with my recent investment in a server setup. However, I’m still learning about server hardware and feel a bit unsure since I don’t have much experience. I managed to assemble everything and finally connected to the web UI on the BMC port, where I was able to configure the system settings. Unfortunately, I accidentally set the manual IP to use VLAN 0, and after applying the changes I couldn’t access the web UI. I’m also struggling to get my home network configured as a VLAN 0. The device still appears in the GBTIPtool during scanning, but the web UI remains unreachable. I’ve tried resetting the CMOS, using jumper settings on the BIOS, and even ran CLI commands to reset the BIOS, but nothing worked. Normally, I expect ID to adjust this setting through the graphical interface when connected to a monitor. I haven’t been able to capture an image from the device yet and am uncertain if there’s another step I’m missing. (I can’t determine the firmware version because the display isn’t working and I can’t get any info from the GBTIPtool, all attempts have failed).

Parts: OS – not installed yet
Gigabyte MZ01-CE0 motherboard, revision 3.0
NEMIX RAM – 64GB (1x64GB) DDR4 2666MHZ (three sticks)
Storage: WD Blue SN580 M.2 2280, 1TB PCI-Express 4.0 x4 (intended for boot drive)
LSI 9300 MegaRAID SAS 9361-8i (LSI00416), PCI-Express 3.0 x8 (will pair with 5 Seagate Exos 7E8 ST4000NM004A 4TB SAS in RAID)
PSU: Seasonic GX-750 80+ Gold AMD EPYC 7601 (current speeds)
Controller and drives are not connected for troubleshooting.
I’m awaiting further guidance from Gigabyte, as I can’t reach the device from the start. Please let me know if there’s anything else I should try.
Reply
Reply
X
x15Ghost15x
04-04-2016, 11:35 AM #1

Hello! I’m really pleased with my recent investment in a server setup. However, I’m still learning about server hardware and feel a bit unsure since I don’t have much experience. I managed to assemble everything and finally connected to the web UI on the BMC port, where I was able to configure the system settings. Unfortunately, I accidentally set the manual IP to use VLAN 0, and after applying the changes I couldn’t access the web UI. I’m also struggling to get my home network configured as a VLAN 0. The device still appears in the GBTIPtool during scanning, but the web UI remains unreachable. I’ve tried resetting the CMOS, using jumper settings on the BIOS, and even ran CLI commands to reset the BIOS, but nothing worked. Normally, I expect ID to adjust this setting through the graphical interface when connected to a monitor. I haven’t been able to capture an image from the device yet and am uncertain if there’s another step I’m missing. (I can’t determine the firmware version because the display isn’t working and I can’t get any info from the GBTIPtool, all attempts have failed).

Parts: OS – not installed yet
Gigabyte MZ01-CE0 motherboard, revision 3.0
NEMIX RAM – 64GB (1x64GB) DDR4 2666MHZ (three sticks)
Storage: WD Blue SN580 M.2 2280, 1TB PCI-Express 4.0 x4 (intended for boot drive)
LSI 9300 MegaRAID SAS 9361-8i (LSI00416), PCI-Express 3.0 x8 (will pair with 5 Seagate Exos 7E8 ST4000NM004A 4TB SAS in RAID)
PSU: Seasonic GX-750 80+ Gold AMD EPYC 7601 (current speeds)
Controller and drives are not connected for troubleshooting.
I’m awaiting further guidance from Gigabyte, as I can’t reach the device from the start. Please let me know if there’s anything else I should try.

Reply
Reply