F5F Stay Refreshed Hardware Desktop Acceleration enhancement technology

Acceleration enhancement technology

Acceleration enhancement technology

Pages (2): Previous 1 2
N
NikoMash
Senior Member
335
08-26-2021, 10:20 PM
#11
The only alternative I considered was looking for BIOS updates. Usually they resolve these problems. You’ll notice the footnote, perhaps mentioning better stability and performance improvements. It might be worth checking. To update the BIOS, refer to the owner’s manual for instructions.
N
NikoMash
08-26-2021, 10:20 PM #11

The only alternative I considered was looking for BIOS updates. Usually they resolve these problems. You’ll notice the footnote, perhaps mentioning better stability and performance improvements. It might be worth checking. To update the BIOS, refer to the owner’s manual for instructions.

M
MarioDX49
Junior Member
22
08-27-2021, 05:03 AM
#12
Thank you all for your assistance, especially Guest 5150—I'll make sure to update the bios.
M
MarioDX49
08-27-2021, 05:03 AM #12

Thank you all for your assistance, especially Guest 5150—I'll make sure to update the bios.

B
Bosskj
Member
100
08-27-2021, 06:14 AM
#13
Auto vcore indicates too much voltage, which is undesirable in a hot operating nuclear reactor
B
Bosskj
08-27-2021, 06:14 AM #13

Auto vcore indicates too much voltage, which is undesirable in a hot operating nuclear reactor

E
Eg9sY
Junior Member
22
08-28-2021, 08:21 PM
#14
It won't exceed any defined boundaries and would remain within power constraints.
E
Eg9sY
08-28-2021, 08:21 PM #14

It won't exceed any defined boundaries and would remain within power constraints.

_
_unknown___
Member
134
08-29-2021, 12:14 AM
#15
remains largely unsuitable, but excluding static issues would make it more acceptable at least for a minor voltage adjustment.
_
_unknown___
08-29-2021, 12:14 AM #15

remains largely unsuitable, but excluding static issues would make it more acceptable at least for a minor voltage adjustment.

X
xp37
Member
60
09-01-2021, 11:50 AM
#16
Just depends on user preference I think. Nothing bad is going to happen. The OP has a decent 360 AIO to move thermals, so there should be no need for any of that. However, none of this is his complaint. So it doesn't really matter at this point.
X
xp37
09-01-2021, 11:50 AM #16

Just depends on user preference I think. Nothing bad is going to happen. The OP has a decent 360 AIO to move thermals, so there should be no need for any of that. However, none of this is his complaint. So it doesn't really matter at this point.

M
Mapley
Member
240
09-01-2021, 03:17 PM
#17
When it begins spinning at 1.3v on a modest 5GHz all-core setup, enjoy pushing limits or simply maxing out performance if your hardware is more capable or the cooling isn't too bad.
M
Mapley
09-01-2021, 03:17 PM #17

When it begins spinning at 1.3v on a modest 5GHz all-core setup, enjoy pushing limits or simply maxing out performance if your hardware is more capable or the cooling isn't too bad.

N
NoahWraith
Member
199
09-03-2021, 08:31 AM
#18
We're discussing the setup for a 5-5.2ghz 10700KF chip. Should I go over it again with the siren?
N
NoahWraith
09-03-2021, 08:31 AM #18

We're discussing the setup for a 5-5.2ghz 10700KF chip. Should I go over it again with the siren?

J
Jarzzermann
Posting Freak
788
09-15-2021, 12:16 PM
#19
The intel safe volt for 14nm (1.52v) isn't realistic for most people since they hit thermal limits long before 1.4v. I don’t see the need for such a complex feature either. Also, getting that spinny siren doesn’t make much sense—if you search for "siren" in the menu, nothing appears.
J
Jarzzermann
09-15-2021, 12:16 PM #19

The intel safe volt for 14nm (1.52v) isn't realistic for most people since they hit thermal limits long before 1.4v. I don’t see the need for such a complex feature either. Also, getting that spinny siren doesn’t make much sense—if you search for "siren" in the menu, nothing appears.

Y
yolosolohi48
Member
167
09-25-2021, 04:34 AM
#20
Thanks for the assistance, but I went into the BIOS, turned on the OC boost, and adjusted the tubo ratio offset for PC cores to 2, which caused it to reach 5GHz all-core turbo.
Y
yolosolohi48
09-25-2021, 04:34 AM #20

Thanks for the assistance, but I went into the BIOS, turned on the OC boost, and adjusted the tubo ratio offset for PC cores to 2, which caused it to reach 5GHz all-core turbo.

Pages (2): Previous 1 2