F5F Stay Refreshed Hardware Desktop Your computer is not functioning properly.

Your computer is not functioning properly.

Your computer is not functioning properly.

X
XxPIZZxX
Member
56
01-22-2023, 10:03 AM
#1
Essentially, your PC has been malfunctioning for some time and you're now working on resolving the issue. It was stuck in a BIOS setting, but after removing it, it won't display on your monitor or shut down properly. You've tried disconnecting one RAM stick and the other, but it didn’t help. What next steps should you consider?
X
XxPIZZxX
01-22-2023, 10:03 AM #1

Essentially, your PC has been malfunctioning for some time and you're now working on resolving the issue. It was stuck in a BIOS setting, but after removing it, it won't display on your monitor or shut down properly. You've tried disconnecting one RAM stick and the other, but it didn’t help. What next steps should you consider?

J
JamesHond7
Posting Freak
838
01-22-2023, 04:49 PM
#2
You asked for detailed system specifications. Your initial actions included clearing the CMOS by removing the silver battery from the motherboard for five minutes, then reinserting it to see if the issue resolved.
J
JamesHond7
01-22-2023, 04:49 PM #2

You asked for detailed system specifications. Your initial actions included clearing the CMOS by removing the silver battery from the motherboard for five minutes, then reinserting it to see if the issue resolved.

P
PewTie
Member
74
01-23-2023, 08:24 AM
#3
The motherboard model is Intel Z690. The pattern of lights on the bottom is likely diagnostic LEDs, often labeled with codes like POST, BIOS, or error messages, which help identify potential hardware issues.
P
PewTie
01-23-2023, 08:24 AM #3

The motherboard model is Intel Z690. The pattern of lights on the bottom is likely diagnostic LEDs, often labeled with codes like POST, BIOS, or error messages, which help identify potential hardware issues.

L
livtheviking
Posting Freak
846
01-23-2023, 02:29 PM
#4
Start simple: stay calm. Based on your info the system is in a POST state, red/blue lights aren’t working and there’s no display. Here’s what to do:

1. Wipe CMOS, turn off the PC, unplug the power supply, remove the CMOS battery for a few minutes or use the jumper if available. Reinsert it and attempt again—this can fix corrupted BIOS settings.
2. Verify RAM placement, ensure all sticks are fully seated until they click. Test with just one stick in slot A2 next to the CPU. If it doesn’t boot, swap it with the other stick in that slot.
3. Reconnect the GPU, making sure it’s attached directly to the GPU rather than the motherboard HDMI (especially if your CPU lacks an integrated graphics).
4. Check power connections—confirm the 24-pin and 8-pin CPU power connectors are securely engaged. Loose cables can trigger this issue.
5. Perform a minimal boot: connect only CPU, one RAM stick, GPU, and PSU. Disconnect all other peripherals. If it still POSTs, reintroduce components gradually.
L
livtheviking
01-23-2023, 02:29 PM #4

Start simple: stay calm. Based on your info the system is in a POST state, red/blue lights aren’t working and there’s no display. Here’s what to do:

1. Wipe CMOS, turn off the PC, unplug the power supply, remove the CMOS battery for a few minutes or use the jumper if available. Reinsert it and attempt again—this can fix corrupted BIOS settings.
2. Verify RAM placement, ensure all sticks are fully seated until they click. Test with just one stick in slot A2 next to the CPU. If it doesn’t boot, swap it with the other stick in that slot.
3. Reconnect the GPU, making sure it’s attached directly to the GPU rather than the motherboard HDMI (especially if your CPU lacks an integrated graphics).
4. Check power connections—confirm the 24-pin and 8-pin CPU power connectors are securely engaged. Loose cables can trigger this issue.
5. Perform a minimal boot: connect only CPU, one RAM stick, GPU, and PSU. Disconnect all other peripherals. If it still POSTs, reintroduce components gradually.