F5F Stay Refreshed Hardware Desktop Windows remains trapped in an automatic repair cycle following RAM replacement.

Windows remains trapped in an automatic repair cycle following RAM replacement.

Windows remains trapped in an automatic repair cycle following RAM replacement.

Pages (2): 1 2 Next
T
TheWilman
Junior Member
Find
2
03-11-2023, 01:05 AM
#1
Reply
Reply
T
TheWilman
03-11-2023, 01:05 AM #1

Reply
Reply
E
Ender_Craft47
Posting Freak
Find
866
03-16-2023, 09:52 AM
#2
Check the current RAM speed. If needed, reset the CMOS to ensure proper settings.
Reply
Reply
E
Ender_Craft47
03-16-2023, 09:52 AM #2

Check the current RAM speed. If needed, reset the CMOS to ensure proper settings.

Reply
Reply
Y
ylyes4
Senior Member
Find
572
03-17-2023, 05:06 AM
#3
3200mhz update completed. CMOS wasn't reset. I recall seeing a possibility of it being a battery connected to the motherboard, though I'm not very familiar with that.
Reply
Reply
Y
ylyes4
03-17-2023, 05:06 AM #3

3200mhz update completed. CMOS wasn't reset. I recall seeing a possibility of it being a battery connected to the motherboard, though I'm not very familiar with that.

Reply
Reply
Y
Yaubarry
Member
Find
204
03-17-2023, 06:10 AM
#4
Reset the UEFI configuration by clearing the CMOS using these options: 1. Navigate to the Exit section in the UEFI and choose Load Optimized Defaults. 2. Locate and press the Clear CMOS button on your motherboard. 3. Disconnect the computer, remove the coin cell battery from the motherboard for a short time, then reattach it.
Reply
Reply
Y
Yaubarry
03-17-2023, 06:10 AM #4

Reset the UEFI configuration by clearing the CMOS using these options: 1. Navigate to the Exit section in the UEFI and choose Load Optimized Defaults. 2. Locate and press the Clear CMOS button on your motherboard. 3. Disconnect the computer, remove the coin cell battery from the motherboard for a short time, then reattach it.

Reply
Reply
M
macmacoo
Member
Find
193
03-17-2023, 09:19 AM
#5
I took all devices off and took the battery out. I left it on for a short time. The screen showed an image, and I pressed F1 to start setup, but the problem still persisted.
Reply
Reply
M
macmacoo
03-17-2023, 09:19 AM #5

I took all devices off and took the battery out. I left it on for a short time. The screen showed an image, and I pressed F1 to start setup, but the problem still persisted.

Reply
Reply
L
leMozaiek
Member
Find
173
03-17-2023, 05:00 PM
#6
Try f2 again next time
Reply
Reply
L
leMozaiek
03-17-2023, 05:00 PM #6

Try f2 again next time

Reply
Reply
F
fahmy
Member
Find
53
03-18-2023, 03:03 PM
#7
Follow Whiro's instructions carefully, ensuring the RAM is properly installed in the slot. If issues persist after this step, please share the details and we'll proceed from there.
Reply
Reply
F
fahmy
03-18-2023, 03:03 PM #7

Follow Whiro's instructions carefully, ensuring the RAM is properly installed in the slot. If issues persist after this step, please share the details and we'll proceed from there.

Reply
Reply
N
Niqhtfall
Member
Find
64
03-18-2023, 03:13 PM
#8
The F1 setup works properly after removing Cmos. You can adjust your time and date if they seem off. Press F10 to save changes and restart, then open Windows. If the error persists, enter safe mode by pressing F8 during boot. Use MSConfig, navigate to the startup section, and check for any installed software that might be causing the problem. Turn off the software, restart, and try again in normal mode. The hardware appears correct; the issue lies with the operating system.
Reply
Reply
N
Niqhtfall
03-18-2023, 03:13 PM #8

The F1 setup works properly after removing Cmos. You can adjust your time and date if they seem off. Press F10 to save changes and restart, then open Windows. If the error persists, enter safe mode by pressing F8 during boot. Use MSConfig, navigate to the startup section, and check for any installed software that might be causing the problem. Turn off the software, restart, and try again in normal mode. The hardware appears correct; the issue lies with the operating system.

Reply
Reply
M
MintyBacca
Junior Member
Find
23
03-18-2023, 05:18 PM
#9
Thanks for your response. I really value your feedback. I was planning to run the system but it didn’t resolve the issue, so I’m now attempting to enter safe mode and remove the MSSA afterburner to determine if that resolves the problem.
Reply
Reply
M
MintyBacca
03-18-2023, 05:18 PM #9

Thanks for your response. I really value your feedback. I was planning to run the system but it didn’t resolve the issue, so I’m now attempting to enter safe mode and remove the MSSA afterburner to determine if that resolves the problem.

Reply
Reply
M
MR_SYKE
Junior Member
Find
41
03-20-2023, 12:28 AM
#10
When you try to access advanced settings in the troubleshooting area, it keeps cycling through the same repair process without changing to safe mode. You might want to restart your PC or consider resetting it if this continues.
Reply
Reply
M
MR_SYKE
03-20-2023, 12:28 AM #10

When you try to access advanced settings in the troubleshooting area, it keeps cycling through the same repair process without changing to safe mode. You might want to restart your PC or consider resetting it if this continues.

Reply
Reply
Pages (2): 1 2 Next