F5F Stay Refreshed Hardware Desktop The SSD fails to be recognized when the CSM is not activated.

The SSD fails to be recognized when the CSM is not activated.

The SSD fails to be recognized when the CSM is not activated.

D
dniznemac
Senior Member
555
03-07-2021, 02:16 PM
#1
Hey everyone, I’m not very familiar with computers, but I just completed my first build with some assistance from a friend. Everything functioned well before this.

Current configuration
- Motherboard: MB- ASUS PRIME X570 PRO
- Processor: RYZEN 5900X
- Graphics card: ASUS ROG STRIX RTX 3070TI OC
- RAM: 2x Corsair Vengeance RGB RT 16GB at 3600MHz DDR4
- Additional RAM: 2x Corsair Vengeance LX 16GB at 3600MHz DDR4
- Storage: WD Black SN850X 1TB M.2 PCIe 4.0 Gen4 x4 NVMe SSD
- Another SSD: WD Black SN770 1TB M.2 PCIe 4.0 NVMe SSD/Solid State Drive

I replaced my CPU from the Ryzen 5600X to the 5900X and added two sticks of RAM (Corsair Vengeance LX DDR4 16GB each at 3600MHz).
After the upgrade, I enabled CMOS, and the PC started booting normally. However, it still didn’t recognize any bootable devices until I turned on the system manager. Once enabled, it boots instantly, but only with the system manager.

When I leave the system manager active, everything works somewhat, though performance remains below expectations. Opening Adobe Animate now takes about a minute to load, and if I interact with the interface before loading, it crashes. Previously, loading took around 30 seconds, which is why I upgraded. Now, with the changes, it’s still not ideal, especially with gameplay stuttering every five seconds.

Any suggestions would be greatly appreciated.
D
dniznemac
03-07-2021, 02:16 PM #1

Hey everyone, I’m not very familiar with computers, but I just completed my first build with some assistance from a friend. Everything functioned well before this.

Current configuration
- Motherboard: MB- ASUS PRIME X570 PRO
- Processor: RYZEN 5900X
- Graphics card: ASUS ROG STRIX RTX 3070TI OC
- RAM: 2x Corsair Vengeance RGB RT 16GB at 3600MHz DDR4
- Additional RAM: 2x Corsair Vengeance LX 16GB at 3600MHz DDR4
- Storage: WD Black SN850X 1TB M.2 PCIe 4.0 Gen4 x4 NVMe SSD
- Another SSD: WD Black SN770 1TB M.2 PCIe 4.0 NVMe SSD/Solid State Drive

I replaced my CPU from the Ryzen 5600X to the 5900X and added two sticks of RAM (Corsair Vengeance LX DDR4 16GB each at 3600MHz).
After the upgrade, I enabled CMOS, and the PC started booting normally. However, it still didn’t recognize any bootable devices until I turned on the system manager. Once enabled, it boots instantly, but only with the system manager.

When I leave the system manager active, everything works somewhat, though performance remains below expectations. Opening Adobe Animate now takes about a minute to load, and if I interact with the interface before loading, it crashes. Previously, loading took around 30 seconds, which is why I upgraded. Now, with the changes, it’s still not ideal, especially with gameplay stuttering every five seconds.

Any suggestions would be greatly appreciated.

G
gavin0099
Member
179
03-07-2021, 03:38 PM
#2
mixing ram? ram memory test?
G
gavin0099
03-07-2021, 03:38 PM #2

mixing ram? ram memory test?

K
kgavaga
Member
112
03-08-2021, 03:18 AM
#3
Yeah I chose not to use RGB because I don't like its appearance anymore. Looking back, I should have picked the same setting.
I'm just starting out and don't know how to perform a RAM memory test.
K
kgavaga
03-08-2021, 03:18 AM #3

Yeah I chose not to use RGB because I don't like its appearance anymore. Looking back, I should have picked the same setting.
I'm just starting out and don't know how to perform a RAM memory test.

M
MrsEveryshot
Junior Member
1
03-09-2021, 05:46 PM
#4
Check out this link:
https://www.techpowerup.com/memtest64/
M
MrsEveryshot
03-09-2021, 05:46 PM #4

Check out this link:
https://www.techpowerup.com/memtest64/