The secondary router's user interface cannot be reached using its IP address.
The secondary router's user interface cannot be reached using its IP address.
The rabbit has presented me with an Easter-related challenge regarding my local network setup. Please help me find a solution to this matter.
A concise overview of the situation: The old secondary router (Mercusys MW325R) connected to my local area network is still visible among available connections, yet I cannot access its user interface for reconfiguration. What steps should I take to restore it?
What I have and what I have tried:
The main router is built into the ISP's modem (KAON CG3002). Its interface can be accessed directly by entering 192.168.0.1. Internet connectivity works through the default gateway as long as the secondary router stays disconnected from the LAN.
When I connect the secondary router, it appears in the network list but is not secured with a password (I only leave it connected briefly).
Before this problem arose, the secondary router was set up as follows:
1. DHCP disabled.
2. Router switched to bridge mode.
Despite several attempts, including a factory reset, the interface remains inaccessible via its URL in the browser.
For reference, the current IP configuration is available via the provided link.
IPCONFIG link
Thank you for your assistance.
No. Avoid using bridge mode.
Bridge mode activates when you link to the main router through Wi-Fi.
Follow these steps:
1. Disable DHCP.
2. Assign a static IP on the LAN interface, ensuring it matches the primary router's network.
For example, if the primary router's LAN address is 192.168.0.1 (mask 255.255.255.0), set the secondary router's LAN address to 192.168.0.2 (mask 255.255.255.0).
3. Connect the secondary router using the LAN port only, not the WAN port.
WAN port is yellow; LAN ports are white.
Please ensure you can enter your current IP address into the browser's address bar. The system will then display the message about the website being unavailable due to connection refusal.
192.168.0.25 is the IP address for your computer, not the secondary router. A factory reset might be useful. Why wouldn't you do it? Try resetting the secondary router instead. Disconnect the secondary router from the network. Plug your PC into the router using the LAN port. Enter the IP address of your secondary router and set it up.
Did you link your computer to the secondary router using a cable (connecting it to the router's LAN port)?
Was only your computer connected to the router, with nothing else?
Turn off all Wi-Fi and Bluetooth connections on your computer.
Make sure the primary router isn't reachable; if so, proceed.
Use the IP address of the secondary router to access it.
Run these commands on your computer:
ipconfig /all
and identify the default gateway, which is the IP address of your secondary router.
Your secondary router seems to be indicating it needs to be placed in a trash can. It’s very outdated and slow. I think there might be an IP conflict. It’s a bit confusing, but the default IP for that device is probably 192.168.1.1. If it restarts, it will likely connect to a different network than your main router.
I recommend unplugging it from your current network, performing a factory reset, and connecting just your PC to the router. Then check your IPCONFIG /all to confirm it’s receiving an IP address in that range from the router. You should be able to enter 192.168.1.1 in a browser to access it.
After that, follow the steps to switch it into AP mode and assign a safe IP in your main network—192.168.0.250 usually works if you’re unsure about the DHCP pool in the primary router.
It’s possible the router has failed. I don’t know the exact model, but 802.11n is nearing its end of life.
Thank you all. I have adjusted the Mercusys router to operate as a wired AP.
So far
- the DHCP server has been disabled, and
- the default gateway is 192.168.0.1
- the main router GUI remains at 192.168.0.1
- LAN IP settings on the Mercusys router are set to Manual.
- The secondary router’s IP address has been updated to 192.168.0.12
Refer to the WAN status in the Mercusys GUI at the provided link:
https://app.screencast.com/Y5GcnAHHVmohy
Check LAN status here: https://app.screencast.com/nQxrOTmYNMuxg
View wireless settings: https://app.screencast.com/txBiKfIxfzlVR
Check ipconfig status: https://app.screencast.com/5De5HZkv1yhDX
Now the connection is secured with a password and offers an additional choice.
My final question: are these configurations suitable if my main aim is for the secondary router to act only as a wired access point?
It looks like these older routers lack many features. I would turn off IPv6 on your computer or the ISP router if possible. It leads to various odd problems and offers almost no advantage. There aren’t many sites that are strictly IPv6-only except for a few in Asia.