F5F Stay Refreshed Hardware Desktop The newly installed RAM isn't functioning properly.

The newly installed RAM isn't functioning properly.

The newly installed RAM isn't functioning properly.

Pages (2): 1 2 Next
H
Hagnarock
Senior Member
434
11-27-2022, 04:02 AM
#1
I purchased two single sticks from TeamGroup at a different time. I reached out to their support and requested an RMA. They shipped the item today, but it remains two single stick RAM units. When trying to run them in single mode, it works fine, yet when both are connected, I encounter BSOD errors like "IRQL DRIVER NIT OR LESS EQUAL WHAT FAILED: e1rqblabla.sys" and "KERNEL SECURITY CHECK ERROR." Possible reasons could include driver conflicts, system instability, or compatibility issues with the hardware.
H
Hagnarock
11-27-2022, 04:02 AM #1

I purchased two single sticks from TeamGroup at a different time. I reached out to their support and requested an RMA. They shipped the item today, but it remains two single stick RAM units. When trying to run them in single mode, it works fine, yet when both are connected, I encounter BSOD errors like "IRQL DRIVER NIT OR LESS EQUAL WHAT FAILED: e1rqblabla.sys" and "KERNEL SECURITY CHECK ERROR." Possible reasons could include driver conflicts, system instability, or compatibility issues with the hardware.

C
CakeSFD
Member
226
11-27-2022, 05:03 AM
#2
The sticker is a USB 3.0 port, and it should be installed on a compatible motherboard with USB 3.0 support.
C
CakeSFD
11-27-2022, 05:03 AM #2

The sticker is a USB 3.0 port, and it should be installed on a compatible motherboard with USB 3.0 support.

G
GameBoosh
Senior Member
470
11-29-2022, 02:58 AM
#3
I didn't include that detail. The Asus X370 Prime Pro uses a Tforce Delta RGB 8GB RAM at 2666MHz. Running both at 2400 or 2666 causes BSOD, but using them separately allows up to 3000MHz.
G
GameBoosh
11-29-2022, 02:58 AM #3

I didn't include that detail. The Asus X370 Prime Pro uses a Tforce Delta RGB 8GB RAM at 2666MHz. Running both at 2400 or 2666 causes BSOD, but using them separately allows up to 3000MHz.

H
Hamoolauae
Junior Member
14
12-07-2022, 12:50 AM
#4
Tforce Delta RGB 8GB RAM 2666MHz. Two sticks available? Yes—reset CMOS then connect both (power off)—use slots A2 and B2.
H
Hamoolauae
12-07-2022, 12:50 AM #4

Tforce Delta RGB 8GB RAM 2666MHz. Two sticks available? Yes—reset CMOS then connect both (power off)—use slots A2 and B2.

E
EntityGlitcher
Junior Member
23
12-08-2022, 12:29 AM
#5
E
EntityGlitcher
12-08-2022, 12:29 AM #5

S
snipper55
Junior Member
13
12-08-2022, 07:08 AM
#6
Thanks for the feedback. It hasn't been my goal to reset the CMOS beforehand. It would normally boot the desktop but then stop after a minute. It's working now and I'm hoping it stays stable. Can I attempt this on a system with 2666MHz? It's currently running at 2400MHz. Edit: Critical Process dies after about 10 minutes. Updated again: Back to IRQL NOT OR LESS EQUAL. Edited November 19, 2019 by heyfritzzapie
S
snipper55
12-08-2022, 07:08 AM #6

Thanks for the feedback. It hasn't been my goal to reset the CMOS beforehand. It would normally boot the desktop but then stop after a minute. It's working now and I'm hoping it stays stable. Can I attempt this on a system with 2666MHz? It's currently running at 2400MHz. Edit: Critical Process dies after about 10 minutes. Updated again: Back to IRQL NOT OR LESS EQUAL. Edited November 19, 2019 by heyfritzzapie

I
iron_finder1
Posting Freak
750
12-08-2022, 08:20 AM
#7
Configure DOCP in BIOS or adjust voltage and timing directly.
I
iron_finder1
12-08-2022, 08:20 AM #7

Configure DOCP in BIOS or adjust voltage and timing directly.

D
DaNiggaSWAG
Senior Member
539
12-08-2022, 12:14 PM
#8
Operating at 2400MHz, I've already faced three BSDs. Will using docp help lessen this issue?
D
DaNiggaSWAG
12-08-2022, 12:14 PM #8

Operating at 2400MHz, I've already faced three BSDs. Will using docp help lessen this issue?

W
WorkOff
Member
145
12-08-2022, 05:18 PM
#9
Configures exact timing and voltage specifications for the selected components. Additionally, think about refreshing the BIOS on the motherboard.
W
WorkOff
12-08-2022, 05:18 PM #9

Configures exact timing and voltage specifications for the selected components. Additionally, think about refreshing the BIOS on the motherboard.

C
Caribbean_Blue
Senior Member
609
12-24-2022, 01:56 AM
#10
Bios is the newest version available. Alright, I'll attempt to configure the docp.
C
Caribbean_Blue
12-24-2022, 01:56 AM #10

Bios is the newest version available. Alright, I'll attempt to configure the docp.

Pages (2): 1 2 Next