The new system XMP mode causes crashes on my PC.
The new system XMP mode causes crashes on my PC.
Hi guys!
When I turned on xmp mode in BIOS so I can run RAM at 2400MHz, my PC crashes after playing any game and some fragments appear. I adjusted the settings manually but still can't get it right and the same happens.
My PC specs:
CPU: Ryzen 3 2200G
RAM: Evo Forza 2400MHz 2x4 DDR4, CL 16/16/16/36
Motherboard: Biostar Racing B350ET2
I want to use my RAM at 2400MHz but it's now running at 2133MHz because of the factory default. Since I'm not very experienced with overclocking, but I'm using a Ryzen 3 2200G Vega 8 graphics card, I really need that 2400MHz for better FPS in games...
Here are some pictures of my BIOS, if anyone can help me figure out what to do, I'll follow their advice! Thanks.
Drea.drechsler shared their experience, mentioning they still faced issues despite attempts. They suggested drivers might be the issue and recommended checking if the memory slots are correctly filled. They noted that Ryzen2k should work with DDR4 2400 at 2400 MHz, and even Ryzen1k could function on older BIOS versions. The person hoped the components came from a supplier with a solid return policy and considered trying a different kit like 2933 or 3000, which support faster memory. They also confirmed success after adjusting VRAM settings in BIOS to specific timings and setting RAM to 2600 MHz.
Does your RAM appear in the motherboard's QVL section, or does it show up as a supported model for that board? If it doesn't, you might not reach its maximum speed.
Is your RAM included in the motherboard's QVL or does it appear as a supported model? If not, you might not reach its rated speed.
There isn't a complete list of compatible RAM on the QVL for my motherboard—it only states: 'This is not a full listing but a memory guide used for testing.'
Ensure your motherboard has the latest BIOS. The most recent versions include updated CPU and RAM specifications. Verify if it remains unstable. Check whether your RAM is Intel-based or AMD. I confirmed it’s the latest version. I adjusted the timing settings slightly, allowing me to boot games now, though fragments persist and crashes occur after about five minutes. Switching back to 2133MHz resolves the issue.
As mentioned before, make sure you're using the most recent BIOS version for your board MFR. Also, confirm that the DIMMs are placed in the two designated sockets as specified in your manual. You should have exactly two DIMMs, not more or less.
If your BIOS includes multiple XMP profiles, try selecting XMP2. This tends to yield better results. If this doesn't succeed, adjusting the timing and voltage settings for your specific DIMM can be effective:
Begin by restarting your system with automatic mode enabled and accessing the BIOS. Manually adjust the RAM speed to 2400. Locate the four digits printed on the DIMM label—typically 16-16-16-36—and input them into the tCL-tRCDRD-tRCDWR and tRAS registers. Keep tRP at its default setting unless you plan to modify it later.
Next, set the DIMM voltage to either 1.30 or 1.35. DDR4 operates well at this level; in fact, 1.45 volts or higher is acceptable, so you might even experiment with higher values if desired. However, once confirmed stable, you can gradually reduce the voltage by small steps of 0.05V.
For Ryzen 2000 chips, a clock speed of 2400 is manageable; they are likely designed to handle up to 2933 MHz. If your DIMMs support it, you should be able to achieve their rated performance.
Good luck!
As mentioned before, make sure you're using the most recent BIOS for your board MFR. Also confirm that the DIMM is placed in the two sockets listed in your manual. Ideally, you should have two and only two DIMMs.
If your BIOS contains multiple XMP settings, try selecting XMP2. This tends to yield better results. If this doesn't resolve the issue, adjusting the timing and voltage parameters for your DIMM often proves effective:
Begin by restarting your system with automatic mode enabled and accessing the BIOS. Manually adjust the RAM frequency to 2400. Locate the four digits printed on the DIMM label (such as 16-16-16-36) and input them into tCL-tRCDRD-tRCDWR and tRAS. Keep tRP at its default setting unless you wish to modify it later to 16 once everything is verified.
Next, adjust the DIMM voltage to 1.30 or 1.35. DDR4 operates well at this voltage; in fact, it performs optimally at 1.45 volts or higher, so you could experiment with even higher values if desired. However, to conserve energy later, once confirmed stable, you can gradually reduce the voltage by 0.05V increments.
For Ryzen 2000 chips, a clock speed of 2400 is not overly demanding; they are likely rated for up to 2933. If your DIMM supports it, you should be able to achieve its maximum speed.
Good luck!
Thanks for the advice!
I double-checked that my BIOS is up-to-date.
I currently have only one XMP profile.
I configured timings as instructed and set RAM voltage first to 1.30 then 1.35, but I still experience crashes.
Then I increased the voltage to 1.45 but the system crashed during login, with graphical artifacts appearing.
I’m not sure what’s happening...
Perhaps adjusting the CPU socket voltage could help?
Zopto_ :
Thanks for advices!
I looked up once again my bios is newset versions.
I only have one XMP Profile
I Set up timings as you said and ram voltage first to 1.30 then 1,35 but i still get crashes
Then i rise voltage up to 1.45 but then windows crashed at log in. and graphical artifacts showed..
Not sure what is going on...
Maybe i should rise cpu socket voltage too??
If you're not overclocking the CPU then you shouldn't have to increase VCore. Same with VSoC on newer BIOS's, especially for Ryzen APU's. So you can try it, but be careful and monitor processor temperature and voltage levels once in booted in Windows. That means using an appropriate utility. If you don't know of any, the motherboard should have come with one on CD or for download from their web site.