The 32GB DDR4 kit with 2x16GB modules isn't stable in XMP mode and drops out even at 3200MHz. It appears to be faulty.
The 32GB DDR4 kit with 2x16GB modules isn't stable in XMP mode and drops out even at 3200MHz. It appears to be faulty.
Hey everyone, I recently upgraded my main board to a 5800x3D with a 32GB G.Skill Ripjaws V 3600 CL16 (F4-3600C16D-32GVKC) setup. It runs on a mini-ITX Gigabyte B450 i Aorus Pro with just two RAM slots. Since then, I've been experiencing instability. This includes crashes when using the XMP 3600 profile (often around 15 minutes into AAA games), occasional hangs and audio issues every couple of minutes, and intermittent freezes even at 3200Hz timings. I thought the mini-ITX speed would allow for stable performance with lower-end RAM, so I skipped higher quality modules. My previous 16GB 2x8GB 3200 kit worked fine at that speed according to timing calculations. The RMA period is over, and there was no seal on the RAM packaging. I ordered it from Amazon Germany three months ago. While the Gigabyte BIOS seems problematic, I’m not sure if I’m missing something obvious. Are these dual-rank 16GB modules prone to issues? I don’t have time to fine-tune timings anymore. Should I install the L and add the RAM to my home server at 2133 MHz, or should I reach out to G.Skill? If the RAM isn’t bad but just of low quality, would a Trident Z Neo kit (150€) or Corsair Vengeance LPX (110€) be better options? Thanks in advance—I’m just starting out as an OG floatplane user and this is my first post.
3600 cl16 refers to a variety of speeds available in that range. Manufacturers often obscure the true specifications by using single numbers and adding unnecessary heat spreaders. XMP auto settings typically work best for RAM in the QVL. If you settle for lower expectations, you may end up needing to adjust settings yourself.
I think a motherboard could be a possibility, but it seems you should check your BIOS first. Try removing a component at a time and test it with games or 7-Zip compression tests to see if performance drops. A dirty or damaged slot might be the issue. If you stick to slower 3200MHz speeds, that’s a clear warning sign. Still, the manufacturer or vendor might assist even outside the RMA window—sometimes they provide replacements for defective parts, and reaching out can help.
Realistic options exist. Older B450 layouts are still around. The B550 isn’t cutting-edge, and the B650 supports AM5.
Gskill model reference: F4-3600C16D-32GVKC 3600MT/s 16-19-19-39 1,35V (intel XMP2). Essentially a budget 3600CL16 built with some high-density 16gbit chips, not Samsung B-Dies. It's hard to confirm the exact processors, but I think it might be a Hynix DJR 16gbit chip. My mainboard isn't listed in the Qualified Vendors List, but since the memory is physically near the socket, it seems unlikely a third party could cause issues—though I wouldn’t rule them out completely. @DaJakerBoss I should have mentioned earlier attempts, but the latest BIOS updates didn’t help. The new chips worked fine after reseating the SODIMM twice; running Windows 10’s built-in memcheck on each stick passed without problems. After raising the CPU voltage to 1.4V, the CMOS cleared successfully. The 7zip compression benchmark is a solid idea! Thanks for the encouragement—it really beats playing BF1 for hours until it crashes. I’m aware of that. I was hoping for a Ryzen 7000, but seeing the overall cost, I gave up and upgraded my older Ryzen 3000-B450 instead.
The quickest cl16 I've encountered is 16-16-16-35. Some models run much slower. Of course, just because it lists cl16 doesn't mean every cl16 RAM is the same. In reality, someone might refer to it as cl19 RAM.
Increase your SOC voltage or adjust the memory controller settings. It might indicate a faulty memory controller. If that fails, the motherboard could be the issue—some models perform better than others. Consider upgrading to a higher-end board like a B550 or X570, though it will cost more.