F5F Stay Refreshed Hardware Desktop System hangs due to continuous restarting after memory addition.

System hangs due to continuous restarting after memory addition.

System hangs due to continuous restarting after memory addition.

C
164
04-16-2016, 06:36 AM
#1
Motherboard: gigabyte Ga-z170xp-sli RAM: 2x8 gigs Corsair 2400MHz CPU: Intel i5 6600K GPU: Nvidia GTX 1070 Power supply: bequiet! E10-CM-600W The issue began during a game session. While chatting on Discord and streaming, my internet browser opened extremely slowly. Upon checking the task manager, I noticed high memory consumption near 80%. This was unexpected since I had 16 gigabytes installed. After verifying, I found only 8 gigabytes remaining. Replacing both RAM modules and turning off the system caused a persistent boot loop. I've tested all possible configurations, cleaned components, reset CMOS, unplugged drives, and replaced the power cable, but the problem persists. Assistance needed.
C
CROSSBOWWEAPON
04-16-2016, 06:36 AM #1

Motherboard: gigabyte Ga-z170xp-sli RAM: 2x8 gigs Corsair 2400MHz CPU: Intel i5 6600K GPU: Nvidia GTX 1070 Power supply: bequiet! E10-CM-600W The issue began during a game session. While chatting on Discord and streaming, my internet browser opened extremely slowly. Upon checking the task manager, I noticed high memory consumption near 80%. This was unexpected since I had 16 gigabytes installed. After verifying, I found only 8 gigabytes remaining. Replacing both RAM modules and turning off the system caused a persistent boot loop. I've tested all possible configurations, cleaned components, reset CMOS, unplugged drives, and replaced the power cable, but the problem persists. Assistance needed.

A
akjosh47
Member
190
04-19-2016, 03:53 PM
#2
You started with one RAM stick (4 slots, 1 occupied). Added a second stick, making it 2 occupied. Then you removed both and replaced them with two new ones.
A
akjosh47
04-19-2016, 03:53 PM #2

You started with one RAM stick (4 slots, 1 occupied). Added a second stick, making it 2 occupied. Then you removed both and replaced them with two new ones.

O
Obeyjoel
Junior Member
2
04-19-2016, 04:45 PM
#3
I initially had two sticks. When I noticed one wasn't detected, I removed and reinserted them in the same positions.
O
Obeyjoel
04-19-2016, 04:45 PM #3

I initially had two sticks. When I noticed one wasn't detected, I removed and reinserted them in the same positions.

E
eskzz
Posting Freak
909
04-19-2016, 06:38 PM
#4
Use a known functional RAM stick, remove the GPU, and run with integrated graphics to test booting.
E
eskzz
04-19-2016, 06:38 PM #4

Use a known functional RAM stick, remove the GPU, and run with integrated graphics to test booting.

S
SIGNORET
Member
160
04-20-2016, 03:24 AM
#5
Confirm if they fit correctly on your motherboard.
Check if other options worked before deciding.
S
SIGNORET
04-20-2016, 03:24 AM #5

Confirm if they fit correctly on your motherboard.
Check if other options worked before deciding.

P
PedroO_
Senior Member
522
04-20-2016, 12:01 PM
#6
I attempted to fit RAM in all available slots and also removed the GPU. Still, the system powers on after swapping out the CMOS battery. Appreciate your efforts!
P
PedroO_
04-20-2016, 12:01 PM #6

I attempted to fit RAM in all available slots and also removed the GPU. Still, the system powers on after swapping out the CMOS battery. Appreciate your efforts!

I
IkBenHetBram
Senior Member
735
04-20-2016, 01:11 PM
#7
The term "boot loop" refers to the system repeatedly restarting without progressing past the initial setup phase. It often involves LEDs flashing or fans spinning, and the screen displaying error messages or codes. This happens when hardware or software issues prevent the PC from loading properly. If you have a mainboard speaker, it typically plays a short beep or tone to indicate a problem. Have you verified the error code?
I
IkBenHetBram
04-20-2016, 01:11 PM #7

The term "boot loop" refers to the system repeatedly restarting without progressing past the initial setup phase. It often involves LEDs flashing or fans spinning, and the screen displaying error messages or codes. This happens when hardware or software issues prevent the PC from loading properly. If you have a mainboard speaker, it typically plays a short beep or tone to indicate a problem. Have you verified the error code?

D
de3gutter
Junior Member
43
04-22-2016, 11:42 AM
#8
No, I didn't clear the CMOS.
D
de3gutter
04-22-2016, 11:42 AM #8

No, I didn't clear the CMOS.