Support for Windows 10 assistance available.

Pages (3): 1 2 3 Next

08-16-2016, 02:46 PM

I completed assembling my new computer and successfully installed Windows the first time. I connected a flash drive, typed in the product key, and the system started restarting for Windows. After that, it asked me to repeat the same steps with the product key. Now it’s showing an error: Windows can’t be installed on Drive 0 Partition 1 or 2.

gootheferret

08-16-2016, 02:46 PM #1

Mr_D_Trump
Junior Member

08-16-2016, 04:32 PM

Your flash drive remains in the backup drive, unsure if you should remove it or not.

Mr_D_Trump

08-16-2016, 04:32 PM #2

Your flash drive remains in the backup drive, unsure if you should remove it or not.

StryKod007
Junior Member

08-24-2016, 07:17 AM

This happens since after installation the system restarts and switches to the USB drive instead of the original hard drive. Disconnect the USB stick and it should launch Windows normally.

StryKod007

08-24-2016, 07:17 AM #3

This happens since after installation the system restarts and switches to the USB drive instead of the original hard drive. Disconnect the USB stick and it should launch Windows normally.

Qemp
Member

137

08-24-2016, 03:42 PM

It sounds like you're stuck on the installation screen and can't choose a partition. Simply disconnecting the USB stick should stop the process, but make sure it's fully unplugged before powering off your PC to avoid data loss.

Qemp

08-24-2016, 03:42 PM #4

Magaveli
Member

135

08-24-2016, 05:21 PM

Since you already have Windows installed, I’d simply power off the machine, remove the USB drive, and restart it from scratch.

Magaveli

08-24-2016, 05:21 PM #5

Since you already have Windows installed, I’d simply power off the machine, remove the USB drive, and restart it from scratch.

MARCEAU973
Junior Member

08-29-2016, 12:48 PM

It mentioned Windows 10 requires a restart before proceeding, but I allowed it to continue and it reset to the start. I’ll power it off and check again.

MARCEAU973

08-29-2016, 12:48 PM #6

It mentioned Windows 10 requires a restart before proceeding, but I allowed it to continue and it reset to the start. I’ll power it off and check again.

funniegame1
Member

192

09-16-2016, 09:19 PM

I think it’s working

funniegame1

09-16-2016, 09:19 PM #7

I think it’s working

xKarlaGamerx
Junior Member

09-30-2016, 04:01 PM

Hello!

xKarlaGamerx

09-30-2016, 04:01 PM #8

Hello!

The_Agent2001
Junior Member

09-30-2016, 04:40 PM

It functioned properly except for the fact that I’m unable to access my Wi-Fi. I own a wireless router, but it’s displaying only Ethernet connections, which I don’t have.

The_Agent2001

09-30-2016, 04:40 PM #9

It functioned properly except for the fact that I’m unable to access my Wi-Fi. I own a wireless router, but it’s displaying only Ethernet connections, which I don’t have.

K31k0
Junior Member

10-01-2016, 12:41 AM

#10

Did you add a WiFi module or does your main board come with built-in Wi-Fi? Otherwise, you must connect an internet cable through the back of your machine to the router.

K31k0

10-01-2016, 12:41 AM #10

Did you add a WiFi module or does your main board come with built-in Wi-Fi? Otherwise, you must connect an internet cable through the back of your machine to the router.

Pages (3): 1 2 3 Next