PC restarts during startup following an overclock adjustment.
PC restarts during startup following an overclock adjustment.
I'm attempting to push my FX 6300 overclock to 4.1 Ghz from its stock 3.5 Ghz, but any attempt triggers the system to restart briefly after powering on before a cold start. Once stabilized, Windows loads normally and temperatures stay below 57°C in the core and 65°C in the socket after about 15 minutes of testing with Prime 95 using C6, C1E, turbo boost, C&Q, and APM disabled. The system uses LLC regular, +100 mv vcore, and +50 mv DRAM. Before adjusting the DRAM voltage, my overclock caused two restarts instead of one before booting. It might be related to the DRAM voltage settings. The PC boots fine with default BIOS if I change nothing else. Should I worry about this issue? What steps can help resolve it? Thanks in advance!
Greasy Pommel :
gussrtk :
Greasy Pommel :
from what you mentioned, it might be wise to perform a stress test on your memory—perhaps you pushed it too far with the RAM?
Other ideas? Consider setting your RAM to AUTO and observing how the system behaves. I’ve tried overclocking my DDR3 motherboard/cpu in several guides, and it turned out no special care was needed unless the overclock was extreme, which it wasn’t.
Setting the RAM to its default voltage didn’t help either. In fact, I raised it to try and fix the issue, as some forums suggested. Could this indicate that I simply received a chip that’s not ideal for overclocking?
Well, it could be you’re being a bit too eager with certain settings. Take a look at...
Based on what you mentioned, it would be wise to perform a stress test on your memory. It’s possible you pushed your RAM too far. Another idea could be to keep your RAM settings at AUTO and observe how the system behaves. From some overclocking guides, it seems no special handling is required unless the overclock becomes very high, which doesn’t seem to be the case here.
from what you mentioned, it might be wise to perform a stress test on your memory. You might have pushed it too far with your RAM? Other suggestions include keeping your RAM settings at AUTO and observing the system behavior. Some guides suggest overclocking DDR3 motherboards or CPUs without much concern for RAM unless the overclock is very high, which doesn’t seem to be the case here. Leaving the RAM voltage unchanged didn’t resolve the issue. I actually raised it in an attempt to address the problem, as advised on certain forums. Could this indicate that you received a chip unsuitable for overclocking?
Greasy Pommel :
gussrtk :
based on what you mentioned, it might be wise to perform a stress test on your memory. You might have pushed yourself too far with the RAM? Other ideas could be to keep your RAM settings at AUTO and observe how the system behaves. I’ve tried overclocking my DDR3 motherboard/cpu in several guides, and it seems unnecessary to adjust the RAM unless you’re planning an extreme overclock. It’s possible you might have selected a chip that isn’t ideal for such adjustments.
Leaving the RAM at its default voltage didn’t resolve the issue. In fact, I increased it to try and fix the problem, as suggested in some forums. This could indicate that I ended up with a chip that struggles under overclocking conditions.
Maybe you’re being too eager with your settings? Check out some guides to confirm everything is configured correctly. Consider lowering the overclock and test again. 4.1 overclock isn’t a major concern... compared to a standard stock setting of around 3.5. Generally, problems appear after an overclock of +1-1.2Ghz.
Gussrtk:
Greasy Pommel :
gussrtk :
Based on what you mentioned, consider performing a stress test on your memory. It’s possible you pushed it too far with the RAM? Other ideas? You might want to keep your RAM settings at AUTO and observe how the system behaves. I’ve tried overclocking DDR3 motherboards and CPUs in various guides, and it seems unnecessary to adjust RAM unless you’re planning extreme overclocks—your setup doesn’t require it.
Leaving the RAM at its default voltage didn’t resolve the issue. In fact, I increased it to try and fix the problem, as suggested by some forums. Could this indicate that I received a chip that’s not suitable for overclocking?
Possibly, you’re being too eager with certain settings. Check the guides carefully, ensure everything is configured correctly. Try reducing the overclock level and see if it improves things. 4.1 overclock isn’t a major concern... compared to a 3.5 stock setup. Generally (from my own overclock experiments), issues tend to appear after an overclock of +1-1.2Ghz.
I’m following some guides to navigate this. The main point is that any overclock, even 3.6Ghz above the stock 3.5Ghz, causes the PC to restart during boot attempts, though it stabilizes after stress tests once it starts.
Greasy Pommel :
gussrtk :
from your words, it seems you should perform a stress test on your memory. You might have pushed it too far with the RAM? Other ideas? Consider keeping your RAM settings at AUTO and observe how the system behaves. I’ve tried overclocking DDR3 motherboards and CPUs in various guides, and it turned out unnecessary to adjust the RAM unless the overclock was very high. This could indicate a problem with a chip that’s not ideal for overclocking.
It might be that you’re being too eager with certain settings. Check some tutorials to confirm everything is configured correctly. Try lowering the overclock and see if it improves things. A 4.1 overclock isn’t a major issue... compared to a stock 3.5, usually problems appear after an overclock of around 1-1.2Ghz.
I’m following some guides to navigate this. The main concern is that even a modest overclock of 3.6Ghz from the stock 3.5Ghz can cause the PC to restart during boot, though it stabilizes after stress tests.
Reset everything to defaults and retry the guide. Look for a manual with your exact model and motherboard. Did you modify the RAM before? (I thought about trying with the original RAM specs.)
Here, it’s not the CPU but the motherboard that differs—this might reveal something you missed.
Greasy Pommel: gussrtk: Greasy Pommel: gussrtk: Based on what you mentioned, it might be wise to perform a stress test on your memory. You may have pushed it too far with the RAM? Other suggestions include keeping your RAM settings at AUTO and observing system behavior. From some overclocking guides for DDR3 motherboards and CPUs, it seems unnecessary to adjust RAM unless the overclock is extreme—your case doesn’t require it. Leaving the RAM at its default voltage didn’t resolve the issue. In fact, I increased it in an attempt to fix the problem, as advised by several forums. This could indicate that you might have selected a chip unsuitable for overclocking. It’s possible you were overly confident with your settings. Review some guides, verify all configurations, and try a lower overclock level. A 4.1 overclock isn’t significant unless it goes beyond +1-1.2Ghz. I’m currently following instructions from online resources. The main concern is that any overclock—even a modest 3.6GHz above stock 3.5GHz—can cause the PC to restart during boot, though it stabilizes after stress testing. Reset everything to defaults and retry the guide. Check if there’s a similar forum with your motherboard for more insight. Did you modify your RAM before trying stock settings? I finally succeeded! I had to dig deeper online, and it seems the issue is widespread among Gigabyte boards when Turbo Boost is turned off. Setting the Turbo Boost multiplier equal to the base value resolves the problem, allowing normal startup. Thank you for your time, and have a great day.