Looking for assistance with boosting the G3258 CPU on an MSI Z97 Mobo?
Looking for assistance with boosting the G3258 CPU on an MSI Z97 Mobo?
Hey everyone,
I'm looking for help with BIOS tweaks to push the G3258 to 4.5GHz on a MSI Z97 PC-Mate Mobo. I've installed the newest BIOS, but OC Genie isn't functioning properly—it doesn't respond when I try to use it. Could anyone suggest any adjustments? Thanks.
Don't exceed the software limits, as programs can't be designed to achieve perfect overclocking. I suggest performing overclocking in BIOS since it requires lower voltage, higher OC, and can extend processor life similar to what software provides. If you follow manual settings, the OC may become unstable and generate more heat. Using too low a voltage can cause instability, while higher voltage increases heat and reduces CPU lifespan. It's crucial to discover the optimal balance between frequency and voltage. To do this, simply follow these steps:
1) activate your XMP memory profile if supported by your memory.
2) raise the CPU ratio from the factory setting...
Don't push the software too hard, as it can't be programmed to achieve perfect overclocking!!! I suggest performing overclocking in the BIOS since it requires less voltage, higher OC, and if you also boost processor life similar to what software offers. Also, if you apply manual settings, the OC may become unstable and generate more heat. Lowering the voltage can cause instability, while raising it increases heat and shortens CPU lifespan. It's crucial to discover a balanced mix of frequency and voltage. To achieve this, follow these steps:
1) Enable your XMP memory profile if supported by your RAM.
2) Slightly adjust the CPU ratio from factory defaults and boot your operating system.
3) Install CPU stress testing software like prime95 and run a test for about 20 minutes.
4) If it succeeds, restart and proceed to BIOS, slightly increasing the CPU ratio again.
5) Repeat step 4 until it succeeds. If not, increase the CPU voltage in BIOS and retest.
6) Eventually, the temperature will rise significantly; stop and let it cool down.
7) While using advanced methods, monitor temperatures closely.
8) You'll reach a point where prime95 fails or the temperature spikes immediately at test start—stop then and enjoy your processor's peak speed. Maintain stable OC and keep temperatures under 80.
Also, refer to the guide I provided earlier for basic guidance. Good luck!
Hello,
I understand that the G3258 can be safely overclocked to 4.5, but I’m unsure about the precise BIOS adjustments required. I’m particularly interested in the MSI Mobo settings modifications.
Navigate to CPU frequency settings>>CPU frequency Ratio, slightly increase it and run a test with prime95. If voltage adjustment is necessary, proceed to Voltage settings>>CPU Vcore (or CPU Voltage) and raise it slightly, then check performance using os and the method described earlier.
I understand it's possible. Even MSI confirms it can be done safely using the stock cooler (refer to below).
http://event.msi.com/mb/2014/pentiumk/
They don't provide the actual BIOS settings, such as clock multiplier and voltage adjustments. That's what I'm after.
Hey guys,
I was thinking if anyone could help me with the BIOS tweaks required to push the G3258 up to 4.5GHz on a MSI Z97 PC-Mate Mobo? I've installed the newest BIOS, but OC Genie isn't responding at all—even when I press the button.
Thanks.
On my motherboard with the CPU, I'm using 1.380 vcore at 45 x 100mhz strap. For your reference, if you reach a point where increasing voltage beyond .050v doesn't boost MHz (my current is 4.3MHz @ 1.280 58°C max), just force the CPU to shut down until the temperature or clock spikes too high—then it's best to leave it alone. (My case was [email protected] 90°C with a 110mm Zalman cooler.) My target daily speed is around 4.5GHz at 1.380v and 72°C max.
I understand this discussion is from over a year ago, but maybe someone can assist. I own the same board CPU setup. I can reach 4.8 stable without any changes except increasing the multiplier. I aim for 5Ghz even by raising the FSB to 105, but if I slightly adjust it to 101, the system won't boot. Is there something I'm missing? Did anyone tell me that socket 1150 processors can't have the FSB altered...?