Issue with XMP profile in BIOS setup

F5F Stay Refreshed Hardware Desktop Issue with XMP profile in BIOS setup

Pages (3): Previous 1 2 3 Next

Devildog36
Member

05-13-2018, 05:54 AM

#11

The XMP profile is set for the RAM at 3000mhz and 1.35v, yet when I apply it in my BIOS the frequency stays at a lower 2133mhz.

Devildog36

05-13-2018, 05:54 AM #11

The XMP profile is set for the RAM at 3000mhz and 1.35v, yet when I apply it in my BIOS the frequency stays at a lower 2133mhz.

cmoney_1
Junior Member

05-13-2018, 07:06 AM

#12

Yes, it aims to enhance memory through three power cycles followed by a boot. After that, it reverts to the default setting of 2133.

cmoney_1

05-13-2018, 07:06 AM #12

Yes, it aims to enhance memory through three power cycles followed by a boot. After that, it reverts to the default setting of 2133.

Weegeeh
Member

165

05-13-2018, 07:16 AM

#13

BIOS settings show 3000 MHz at 1.35V, yet the XMP profile listed is 2133 MHz. This discrepancy matches what I mentioned earlier.

Weegeeh

05-13-2018, 07:16 AM #13

BIOS settings show 3000 MHz at 1.35V, yet the XMP profile listed is 2133 MHz. This discrepancy matches what I mentioned earlier.

ImRico
Junior Member

05-13-2018, 11:32 AM

#14

That's what occurs when I exceed 3000MHz, hehe

ImRico

05-13-2018, 11:32 AM #14

That's what occurs when I exceed 3000MHz, hehe

Radtack_
Junior Member

05-14-2018, 04:41 AM

#15

I don't recognize a power cycle yet, so it's unclear what you mean. However, when I turn on the lights, they only flicker once. (LED/RGB)

Radtack_

05-14-2018, 04:41 AM #15

I don't recognize a power cycle yet, so it's unclear what you mean. However, when I turn on the lights, they only flicker once. (LED/RGB)

DaDoxOP
Junior Member

06-01-2018, 08:43 AM

#16

It seems the system frequently encounters a blue screen when exceeding 2866, indicating a "page fault in nonpaged area" error.

DaDoxOP

06-01-2018, 08:43 AM #16

It seems the system frequently encounters a blue screen when exceeding 2866, indicating a "page fault in nonpaged area" error.

Streiyn
Posting Freak

768

06-03-2018, 07:01 PM

#17

It increases speed and stops, then repeats the process, finally shutting down.

Streiyn

06-03-2018, 07:01 PM #17

It increases speed and stops, then repeats the process, finally shutting down.

missingmetal
Member

181

06-04-2018, 03:52 AM

#18

The multiple power cycles suggest memory training has not succeeded.

missingmetal

06-04-2018, 03:52 AM #18

The multiple power cycles suggest memory training has not succeeded.

EnderSoul2006
Junior Member

06-11-2018, 05:39 AM

#19

The computer isn't running as many cycles during startup.

EnderSoul2006

06-11-2018, 05:39 AM #19

The computer isn't running as many cycles during startup.

Pixel_Cupcake
Junior Member

06-15-2018, 07:03 PM

#20

I get it, it's just a joke since it's my mistake and not XMP's.

Pixel_Cupcake

06-15-2018, 07:03 PM #20

I get it, it's just a joke since it's my mistake and not XMP's.

Pages (3): Previous 1 2 3 Next