Desk advice
Desk advice
Achieving the desired height is straightforward. You obtain a few kits and then adjust the tubes to match the exact height needed for your desk. These units are quite sturdy, having supported heavy audio gear on my desk for over a year and a half without any problems. I even had to modify them myself to fit the low ceiling height in my basement.
I'm considering this idea:
bench top
They are available in lengths of 60 and 72 inches.
with these features:
hair pin legs
They come in heights of 24, 26, and 28 inches.
That would result in an overall height ranging from 26.25 to 29.25 inches.
I'm still searching through the file cabinet for one end.
Adding a cable tray underneath and a few additional features would make it both functional and stylish.
These appear to be solid choices. When dealing with something like this, it's important to allocate a bit of time and avoid being swayed by the first option that seems promising. Once you've made a decision, you might discover a superior alternative after further research.
If you opt for the bench top, which seems like a reasonable choice, I suggest considering six legs instead of four. Having two at each end and two in the center could be beneficial, allowing you to assess necessity later and add more if needed.
Additionally, it would be wise to consult local custom laminate or custom wood countertop builders and manufacturers. Often, I can obtain items tailored to my specifications or find unsold pieces at a significantly reduced price from nearby stores that store them in containers or storage areas. I've previously purchased 72-inch laminated countertops for around fifty dollars, which is considerably less than the typical cost at big-box retailers like Lowe's or Home Depot.
Moreover, local custom countertop shops may be able to produce items without backsplashes, which is ideal for a desk setup. They could also offer options with either no backsplash or decorative edges on both sides, enhancing the overall design. It's always a good idea to inquire about these possibilities.
I returned the desk I had. It was acceptable, though the drawers obstructed the space and the desk was too short. I’ll keep this post for others to review if they’re interested. I swapped it with a different desk in my next photo below.
At Home Depot, I discovered the Husky work benches and chose the 52-inch model. They offer sizes ranging from 46 to 72 inches, with white or black frames and natural wood tops—either oak or ash. The bottom drawer serves as a keyboard tray, while the top drawer will function as a key caddy. If the drawers don’t suit you, they’re removable, and there’s also a drawerless version. The top dimensions are 52x24 inches, with adjustable height from 26 to 42 inches. It includes casters with leveling feet, though you can opt for a different configuration. The frame appears to be constructed from 11-gauge sheet metal and has a powder-coated finish. The drawers are thinner metal but offer 30-pound capacity, and the table supports up to 300 pounds.
I’m currently in test mode, so I’ll let you know about the cable organization next time.
Certainly not the worst option at all. Likely superior to any of those adjustable height desks we discussed.
The section where you place the mouse and keyboard follows a drawer-style layout. Only part I doesn't appeal to you. You position your hands on that metal bar, which is significantly higher than the keyboard and mouse, right?
It could actually be quite straightforward if someone really tried. You've probably noticed drawers that open by flipping the front down, and you can easily find hinges online for a reasonable price. However, beyond that, you'd need a metal cutting reciprocating saw, a pneumatic tool, or something like a Dremel or angle grinder with a thin blade to remove the entire drawer front from behind. You could then secure the hinge to the drawer and either use epoxy or weld it in place with a tack weld, avoiding visible screws. Even if you do use screws, using decorative ones could make it look better. Personally, I think it might be more practical for a DIYer, and it could be done affordably. Alternatively, you might simply place a larger board higher than the drawer and slide it in when needed, keeping it out of the way when not in use.
the compartments measure just 1.5 inches and can be taken off.
The reviewers agreed with the feedback. The drawer sizes and height didn’t suit a gaming or office setup. The 50-inch length was the main concern, as it limited available desk space. I returned it after a short period.
During that time, I received a 72-inch UltraHD adjustable workbench from Sam's Club. This desk stands out as the most well-built I’ve experienced. After some hesitation, I gave it a try after a few weeks. It works perfectly for me.
Desk-workbench from Sam's Club
Last week I purchased a Secretlab Titan chair. They’re currently on sale for $399. The Ash color has a 2/24 shipping date.
The desk is low to the ground, which suits my preference for matching desk height and armrests to maintain wrist neutrality. I have carpal tunnel issues in both hands due to 30 years of working as a CADD designer and gamer.