F5F Stay Refreshed Hardware Desktop Critical: Processor activated the cooling system, but it remains obstructed by the cooler.

Critical: Processor activated the cooling system, but it remains obstructed by the cooler.

Critical: Processor activated the cooling system, but it remains obstructed by the cooler.

Pages (3): 1 2 3 Next
B
boricua2006
Junior Member
7
12-07-2018, 03:56 PM
#1
I was taking out the Wraith Prism cooler while watching a tutorial to remove it. However, the CPU popped up with the cooler and seems stuck, as if it’s super glued to the processor. This is my AMD Ryzen 7 2700x and Wraith Prism cooler. Note: I’ve had this PC since January 2019, and the thermal paste that came pre-applied on the cooler is still there.
B
boricua2006
12-07-2018, 03:56 PM #1

I was taking out the Wraith Prism cooler while watching a tutorial to remove it. However, the CPU popped up with the cooler and seems stuck, as if it’s super glued to the processor. This is my AMD Ryzen 7 2700x and Wraith Prism cooler. Note: I’ve had this PC since January 2019, and the thermal paste that came pre-applied on the cooler is still there.

K
KawiianMili
Posting Freak
786
12-08-2018, 04:21 AM
#2
Upload limit reached at 20 MB; images must be sent separately
K
KawiianMili
12-08-2018, 04:21 AM #2

Upload limit reached at 20 MB; images must be sent separately

B
BobFortier
Member
182
12-25-2018, 10:34 AM
#3
This situation is possible. Carefully remove the CPU from the HSF.
B
BobFortier
12-25-2018, 10:34 AM #3

This situation is possible. Carefully remove the CPU from the HSF.

_
_EVIX_
Member
57
12-26-2018, 02:43 AM
#4
Manipulate it carefully, avoid bending the pins too much. Rotate it extensively; eventually it should release. Be cautious. Then test whether it reinserts smoothly without the locking bar in place. If not, inspect for bent or absent pins.
_
_EVIX_
12-26-2018, 02:43 AM #4

Manipulate it carefully, avoid bending the pins too much. Rotate it extensively; eventually it should release. Be cautious. Then test whether it reinserts smoothly without the locking bar in place. If not, inspect for bent or absent pins.

Z
Zen_Browncoat
Junior Member
8
12-26-2018, 07:01 AM
#5
Hold the sides of the CPU with your fingers and gently shake it off. Apply pressure slightly, then adjust direction, rinse, and continue the process.
Z
Zen_Browncoat
12-26-2018, 07:01 AM #5

Hold the sides of the CPU with your fingers and gently shake it off. Apply pressure slightly, then adjust direction, rinse, and continue the process.

P
pokejess
Junior Member
17
12-27-2018, 03:24 AM
#6
Suggest using a hair dryer to heat the paste, then carefully remove it. Be cautious as it may split unexpectedly if the thermal paste is too cold. Always perform a 5-10 minute CPU stress test before taking it out.
P
pokejess
12-27-2018, 03:24 AM #6

Suggest using a hair dryer to heat the paste, then carefully remove it. Be cautious as it may split unexpectedly if the thermal paste is too cold. Always perform a 5-10 minute CPU stress test before taking it out.

D
Dijogani
Member
57
01-06-2019, 01:44 PM
#7
I've confirmed everything is aligned. I'm hoping it remains this way.
D
Dijogani
01-06-2019, 01:44 PM #7

I've confirmed everything is aligned. I'm hoping it remains this way.

D
danielitax3
Junior Member
35
01-06-2019, 05:24 PM
#8
I shared this on the forum about steps to follow before taking apart a PC, but no one mentioned it. What a surprise!
D
danielitax3
01-06-2019, 05:24 PM #8

I shared this on the forum about steps to follow before taking apart a PC, but no one mentioned it. What a surprise!

Z
Ziegelcraft
Member
58
01-15-2019, 12:36 AM
#9
I'm worried, it's not happening.
Z
Ziegelcraft
01-15-2019, 12:36 AM #9

I'm worried, it's not happening.

S
Slayed_Dragon
Member
63
02-05-2019, 05:16 PM
#10
Refer to the previous note about warming dental floss.
S
Slayed_Dragon
02-05-2019, 05:16 PM #10

Refer to the previous note about warming dental floss.

Pages (3): 1 2 3 Next