Continuous BSOD occurrences

F5F Stay Refreshed Hardware Desktop Continuous BSOD occurrences

Pages (2): Previous 1 2

192

04-07-2020, 08:54 PM

#11

Different options available, including unusual BSoD messages I haven’t encountered before. Recommendations: (1) Update BIOS and reset everything in the BIOS to default settings. (2) Fresh install of Windows 10. (3) If problems persist, check RAM or motherboard.

funniegame1

04-07-2020, 08:54 PM #11

GOMERO_LDP
Junior Member

04-08-2020, 12:28 PM

#12

I have the most recent bios ready, but I’m unsure about resetting everything. After a fresh Windows installation, you usually download the installer to a pen and follow the normal driver setup process. If you skip formatting during Windows setup, it might affect recovery options.

GOMERO_LDP

04-08-2020, 12:28 PM #12

NewKing
Junior Member

04-15-2020, 06:35 PM

#13

Reset your BIOS by clearing the CMOS. Look in your motherboard’s guide for steps—often a switch or button works—or remove the power source briefly.

NewKing

04-15-2020, 06:35 PM #13

Reset your BIOS by clearing the CMOS. Look in your motherboard’s guide for steps—often a switch or button works—or remove the power source briefly.

HBD3051
Junior Member

04-15-2020, 09:56 PM

#14

Sure, I understand. If you reset the BIOS, the version might revert to the original factory setting. For your Ryzen 5 3600, you may want to keep the older version if needed.

HBD3051

04-15-2020, 09:56 PM #14

Sure, I understand. If you reset the BIOS, the version might revert to the original factory setting. For your Ryzen 5 3600, you may want to keep the older version if needed.

MrKryp
Senior Member

643

04-16-2020, 02:04 AM

#15

Performing a CMOS reset restores your system to its original BIOS configuration rather than updating it.

MrKryp

04-16-2020, 02:04 AM #15

Performing a CMOS reset restores your system to its original BIOS configuration rather than updating it.

DanKaneki
Junior Member

04-16-2020, 08:54 AM

#16

Yes, it matches the version labeled "1.1.6" for the jumper.

DanKaneki

04-16-2020, 08:54 AM #16

Yes, it matches the version labeled "1.1.6" for the jumper.

maddixcraft
Junior Member

04-16-2020, 12:51 PM

#17

Chapter 1.1.6 on pages 1 through 9 matches the guide you need.

maddixcraft

04-16-2020, 12:51 PM #17

Chapter 1.1.6 on pages 1 through 9 matches the guide you need.

Kiropie38
Junior Member

04-16-2020, 01:51 PM

#18

I'll handle it later after work. I usually save the Windows installer to a pen, boot it, and choose format during driver setup. It's quicker—about three seconds—and it formats the drive directly. Alternatively, you can go to Settings and try Reset PC if needed.

Kiropie38

04-16-2020, 01:51 PM #18

SACHINKA
Member

04-22-2020, 02:43 PM

#19

You should proceed with removing all partitions via the Windows installer, then place the installation in the unallocated space. The installer will handle the rest automatically.

SACHINKA

04-22-2020, 02:43 PM #19

You should proceed with removing all partitions via the Windows installer, then place the installation in the unallocated space. The installer will handle the rest automatically.

Pages (2): Previous 1 2