Adjust the PC case fan to operate continuously or pause as needed.

F5F Stay Refreshed Hardware Desktop Adjust the PC case fan to operate continuously or pause as needed.

Pages (3): Previous 1 2 3 Next

xeal987
Member

11-12-2023, 11:28 AM

#11

I've connected it and then unplugged it, but it still didn't work.

xeal987

11-12-2023, 11:28 AM #11

I've connected it and then unplugged it, but it still didn't work.

MrBobBoberson
Junior Member

11-12-2023, 11:53 AM

#12

Is it unusual? Do you know someone with a PC you could connect to test the fans? That way we can eliminate other possibilities and focus on the hub if it doesn't work.

MrBobBoberson

11-12-2023, 11:53 AM #12

Is it unusual? Do you know someone with a PC you could connect to test the fans? That way we can eliminate other possibilities and focus on the hub if it doesn't work.

DylanParkerrrr
Junior Member

11-12-2023, 07:51 PM

#13

sorry, I'm unable to test it.

DylanParkerrrr

11-12-2023, 07:51 PM #13

sorry, I'm unable to test it.

primoalanchris
Member

137

11-16-2023, 08:09 AM

#14

Insert a few of the fans into the motherboard slots, which should help eliminate any concerns about them.

primoalanchris

11-16-2023, 08:09 AM #14

Insert a few of the fans into the motherboard slots, which should help eliminate any concerns about them.

AwesomeIce1121
Member

201

11-16-2023, 03:07 PM

#15

and by the way, three of my supporters are doing the same thing linked to this hub

AwesomeIce1121

11-16-2023, 03:07 PM #15

and by the way, three of my supporters are doing the same thing linked to this hub

SmartBoysFart
Member

211

11-18-2023, 02:36 PM

#16

my fan is 6-pin but i don't have a 6-pin connector on my motherboard, it's only 4-pin

SmartBoysFart

11-18-2023, 02:36 PM #16

my fan is 6-pin but i don't have a 6-pin connector on my motherboard, it's only 4-pin

Fletcher45
Junior Member

11-18-2023, 04:17 PM

#17

Checked the setup, these are unusual fan connectors with MB sync and Molex power. Fans should be installed sequentially from positions 1 to 8. Confirmed it’s correct.

Fletcher45

11-18-2023, 04:17 PM #17

Checked the setup, these are unusual fan connectors with MB sync and Molex power. Fans should be installed sequentially from positions 1 to 8. Confirmed it’s correct.

Montykins
Member

11-22-2023, 10:04 PM

#18

yes i did

Montykins

11-22-2023, 10:04 PM #18

yes i did

AstroZone
Member

136

11-29-2023, 04:03 PM

#19

I believe it's the hub—pressing the button from there doesn't help, while the fan keeps spinning and then stops without any RGB changes.

AstroZone

11-29-2023, 04:03 PM #19

I believe it's the hub—pressing the button from there doesn't help, while the fan keeps spinning and then stops without any RGB changes.

MrTurtleLover
Member

243

12-07-2023, 01:48 AM

#20

From what I observe, everything seems to be functioning properly. The hub supplies power and the fans operate based on commands from the hub without any motherboard involvement. These are likely the same fans that have been running previously and just paused recently.

MrTurtleLover

12-07-2023, 01:48 AM #20

Pages (3): Previous 1 2 3 Next